Planter Reduce Unnecessary Load

- Jul 13, 2017-

Planer standard operating procedures

For farmers friends, the planter is no longer a strange agricultural products, but to become their annual spring are necessary agricultural equipment, from the initial artificial cultivation to the present full mechanization operation, but for some special plots such as: Mountains, hills, or some small area of cultivated land can not use large equipment, so it is necessary to apply to the seeder, then you understand the standard use of the programmer it?

1, the new purchase of the planter, in accordance with the instructions assembly products (simple steps, no special cumbersome assembly process); if it is last year's product, be sure to check whether the parts of the problem.

2, after the completion of the assembly to pay attention to debugging, because the land of different regions, so the density is not the same. You can experiment at home, and then make a reasonable adjustment.

3, field operations, pilot about 10-30 meters, in accordance with the specific circumstances of debugging, if no problem to start planting work.

Note when planting:

Be sure to pay attention when planting, can not pull down, push and other operations, so as not to sowing the internal gear damage. Seeds, fertilizers to avoid loading over full, while the amount of fertilizer must not be less than one-fifth of the fertilizer box. Sowing must be uniform before the line, can not covet the speed of planting fast to run quickly and so on.

At the end of the planting, follow the assembly procedure of the first step to remove the sowing device, clean up the soil and so on. Do not store in the direct sunlight and rain can be poured to the place, not easy to use the next year.

How to make the seeder use more long

How can we let the sower use for a longer time, let's take a brief look.

Before using the sowing device: If you are using the product of the previous year, then you need to check the saddler gear transmission parts, and check whether the normal operation of parts, with lubricating oil for conservation is the best, there is a need Check the spring components corresponding to each component, if loose must be replaced in time.

When used: in accordance with the technical requirements of manufacturers to install, fertilizer box should not be loaded over full, do not vigorously when sowing.

After use: thoroughly clean the seed box, the sower placed in a ventilated and dry warehouse, if it is open storage, the sowing device to cover and other operations, in order to prevent damage to parts, you can carry out disassembly and storage.

So, if you want the sower to be used for a longer time, you have to know how to keep it in order to ensure that the seeder exerts its greatest effect to extend the life of the seeder.

The use of the seeder points and the use of points

1, do a good job before the maintenance of the field operations. To clean up the sowing of the debris and the opener on the opener. Soil, to ensure good condition, and tractors and corn planter of the drive. Rotate the parts, according to the requirements of the instructions filling lubricants, in particular, pay attention to the transmission chain lubrication and tension and the bolt on the planter fastening.

2, corn planter and tractor hook, not tilted, the work should be before and after the rack was horizontal state.

3, do a variety of adjustments. According to the instructions and agronomic requirements, will be sowing the amount of opener spacing. The depth of the trenching casing is appropriate.

4, before and after the work of each class and work, the parts of the soil should be clean, pay special attention to clear the transmission system on the soil, oil.

5, after each shift, the planter should be parked in a dry covered shed. When the open air is parked, When the parking is dropped, the opener is lowered and the restraint is lowered to stabilize the body so that the load on the rack of the planter is reduced.

(6) to prevent the hand, feet and clothes touch the rotating parts.

(7) wear tight clothes to avoid being wound by moving parts.

(8) When lifting or transporting the planter, be careful of wires, trees, etc., transport speed can not exceed 32 km, driving on the road should use flash warning lights and turn on the lights, pay attention to the size of the transport, especially when the planter width is greater than the tractor Time.

(9) For traction planters, the turning radius should not be too small, otherwise the sowing machine squeezes the wheel, which may cause personal injury or damage to the equipment.

(10) Before maintenance, drop or firmly support the planter, park the tractor, turn off the engine, ensure that all moving parts stop working and reduce all system pressure. Use the correct tools and equipment for repair and replacement.